产品展示
供应欧莱斯1300金属油墨-欧莱斯1300油墨-1300油墨
【简单介绍】
【详细说明】
1300系列是对各种金属、金属涂漆面进行网版印刷之用,对要求粘合性、耐药品性时使用本油墨,与1000系列、1690系列的二液型环氧(EPOXY)油墨不同,1300系列是内含催化剂的一液性、以烘焙干燥为前提的环氧油墨。
油墨类型:将特殊合成树脂与环氧树脂(EPOXYRESIN)混合而成的一液性加热硬化型油墨。一般这种油墨需要高温烘焙。
用 途:铝、镀锌铁板、不锈钢、铁及这些的涂漆板,zui适于铭板、电气用品、标牌等的印刷。
外 观:有光泽,可得平滑的成品。
干燥条件:以加热干燥为前提。加热干燥的标准条件是以150度加热30分钟。
稀 释:粘度调整用T-1000,以油墨100对10-15才是适当。The 1300 series is all kinds of metal, metal to paint surface nets printing with, the requirement for bonding sex and drug resistance in the use of the printing ink, and series 1000, series 1690 two fluid type EPOXY (EPOXY) ink is different, the 1300 series is a liquid containing catalysts to baking dry sex, the premise of EPOXY printing ink. Ink type: special synthetic resin and epoxy resin (EPOXYRESIN), which is a mixture of a liquid heating sclerosis type printing ink. Usually this ink need high temperature baking. With the way: aluminum, galvanized iron, stainless steel, the iron and the paint on the board, the most suitable for the name plate, electrical appliances, brands such as printing. The view: the luster, smooth finished products. Dry conditions: to the heating dry as the prerequisite. Heating dry conditions is the standard of 150 degrees heating 30 minutes. Rare shih: viscosity with T-1000 adjustment to ink to 100 10-15 is appropriate. Stick close: to metal and paint surface and so on has strong adhesion sex. Other note: 1) the 1300 series is based on baking is the prerequisite for dry the performance of the good play, but for outdoor exposure dew products (signs, and mark etc), when use special effects by moisture in special color epoxy resin coating from separation phenomenon, so please note. 2) the 1300 series is based on baking as the premise, and therefore should be kept in storage measunnent of the cold dark place less influence.
粘 合:对金属及涂漆面等具有强粘合性。
其他注意事项:
1)1300系列是以烘焙干燥为前提发挥优秀的性能,但对室外曝光露制品(招牌、标志等),在使用时特别受湿气影响而成环氧树脂*的颜色从涂料分离现象,故请注意。
2)1300系列是以烘焙为前提,因此储藏时应保管在外气影响少的冷暗处保管。
3)1300系列以硬化剂催化干燥,但有时内置的硬化剂受外气影响或保存时间太长,催化性能减弱。这时将1300H催化剂以1%以内(重量比)补充时就可以保持本来的性能。因此,要*保存的制品应试验确认后再行使用。
4)1300系列底色墨过于硬化时,叠印粘合性会降低而脱落。进行多色叠印时底下层油墨只能短时间烘干,即可在上面再印,全部颜色印完后正常干燥*。
5)1300油墨应用在玻璃制品时,和金属及其涂漆面的印刷物相比,在耐水耐湿性方面稍会降低,请注意。
#1300油墨印刷啤模性能表:
油墨类型:将特殊合成树脂与环氧树脂(EPOXYRESIN)混合而成的一液性加热硬化型油墨。一般这种油墨需要高温烘焙。
用 途:铝、镀锌铁板、不锈钢、铁及这些的涂漆板,zui适于铭板、电气用品、标牌等的印刷。
外 观:有光泽,可得平滑的成品。
干燥条件:以加热干燥为前提。加热干燥的标准条件是以150度加热30分钟。
稀 释:粘度调整用T-1000,以油墨100对10-15才是适当。The 1300 series is all kinds of metal, metal to paint surface nets printing with, the requirement for bonding sex and drug resistance in the use of the printing ink, and series 1000, series 1690 two fluid type EPOXY (EPOXY) ink is different, the 1300 series is a liquid containing catalysts to baking dry sex, the premise of EPOXY printing ink. Ink type: special synthetic resin and epoxy resin (EPOXYRESIN), which is a mixture of a liquid heating sclerosis type printing ink. Usually this ink need high temperature baking. With the way: aluminum, galvanized iron, stainless steel, the iron and the paint on the board, the most suitable for the name plate, electrical appliances, brands such as printing. The view: the luster, smooth finished products. Dry conditions: to the heating dry as the prerequisite. Heating dry conditions is the standard of 150 degrees heating 30 minutes. Rare shih: viscosity with T-1000 adjustment to ink to 100 10-15 is appropriate. Stick close: to metal and paint surface and so on has strong adhesion sex. Other note: 1) the 1300 series is based on baking is the prerequisite for dry the performance of the good play, but for outdoor exposure dew products (signs, and mark etc), when use special effects by moisture in special color epoxy resin coating from separation phenomenon, so please note. 2) the 1300 series is based on baking as the premise, and therefore should be kept in storage measunnent of the cold dark place less influence.
粘 合:对金属及涂漆面等具有强粘合性。
其他注意事项:
1)1300系列是以烘焙干燥为前提发挥优秀的性能,但对室外曝光露制品(招牌、标志等),在使用时特别受湿气影响而成环氧树脂*的颜色从涂料分离现象,故请注意。
2)1300系列是以烘焙为前提,因此储藏时应保管在外气影响少的冷暗处保管。
3)1300系列以硬化剂催化干燥,但有时内置的硬化剂受外气影响或保存时间太长,催化性能减弱。这时将1300H催化剂以1%以内(重量比)补充时就可以保持本来的性能。因此,要*保存的制品应试验确认后再行使用。
4)1300系列底色墨过于硬化时,叠印粘合性会降低而脱落。进行多色叠印时底下层油墨只能短时间烘干,即可在上面再印,全部颜色印完后正常干燥*。
5)1300油墨应用在玻璃制品时,和金属及其涂漆面的印刷物相比,在耐水耐湿性方面稍会降低,请注意。
#1300油墨印刷啤模性能表:
相关产品
产品搜索
请输入产品关键字:
联系方式
包装印刷产业网 设计制作,未经允许翻录必究.Copyright(C) https://www.ppzhan.com, All rights reserved.
以上信息由企业自行提供,信息内容的真实性、准确性和合法性由相关企业负责,包装印刷产业网对此不承担任何保证责任。
温馨提示:为规避购买风险,建议您在购买产品前务必确认供应商资质及产品质量。
以上信息由企业自行提供,信息内容的真实性、准确性和合法性由相关企业负责,包装印刷产业网对此不承担任何保证责任。
温馨提示:为规避购买风险,建议您在购买产品前务必确认供应商资质及产品质量。