体积电阻率、表面电阻率测定仪

本仪器是既可测量高电阻，又可测微电流。采用了美国In公司的大规模集成电路以及技术,使仪器体积小、重量轻、准确度高。以双3.1/2 位数字直接显示电阻的高阻计和电流。量限从1×104Ω ～1×1018 Ω，是目前国内测量范围Z宽，准确度Z高的数字超高阻测量仪。电流测量范围为2×10-4 ～1×10-16Ａ。机内测试电压为10/50/100/250/500/1000V任意可调。本仪器具有精度

北京北广精仪仪器设备有限公司郑重声明：* ，如有需要：请搜索（北京北广精仪仪器设备有限公司）

体积电阻率表面电阻率测试仪  型号：BEST-121

五、仪器特征

本仪器测量采用三电极法对试样进行测试，其试验装置主要有平板式电极装置和高阻计两部分组成。基本原理是对试样加入不同挡位的直流电压，流经试样的微弱电流用标准电阻取样放大后，从高阻计上读出。数字直接显示出电阻值,精度高、显示迅速、稳定性好、读数方便。技术指标1、采用高集成度的3 1/2位数字显示。2、量程范围：1×105Ω ～1.999×1014 Ω

3、测试电压为DC100V或DC500V或用户订制

4、工作环境温度：20℃±2℃，湿度：35%±10%RH

5、仪器在稳定的工作电压及无信号输入时1--8小时之间零点漂移小于±5%

6、仪器对标准电阻测量的基本误差：≤±10% 

六、 技术参数 

·         型 号 SB36固体（液体）体积电阻率及表面电阻率测试仪

·         额定电压 10 100 250 500 1000 准确度 ±5 % 

·         电阻测量 1* 106～1* 1017准确度 ±10 % ±20 % 

 ·         微电流测量 1* 105～1* 1014准确度 ±10 % ±20 % 

·         外形尺寸/重量（MM /KG） 380W * 260D * 150H / 10 主要用途及特点: 

·         适用于科研、工厂、学校、企业部门对绝缘材料、电工产品、电子设备以及元件的绝缘测量和高阻值兆欧电阻的测量也可用着微电流测量，是一种直读式和微电流两用仪器。 

测试电压（V） 误 差 

DC—10V ±5% 

DC—50V ±5% 

DC—100V ±5% 

DC—500V ±5% 

DC—1000V ±5% 

Volume resistivity of surface resistivity tester

Digital high resistance, a current measuring instrument type: EST-121: volume resistivity, surface resistivity uses: Instrumentation Test

One, volume resistivity surface resistivity tester overview

This instrument can measure high resistance, and measuring current. The American company In large scale integrated circuit and patented technology, the instrument has the advantages of small volume, light weight, high accuracy. Dual 3.1/2 digital display the resistance high resistance meter and current. Limit from 1× 104 Ω～ 1× 1018 Ω, is currently the most wide measurement range, the most accurate digital ultra high resistance meter. Current measurement range of 2× 10-4 ～ 1× 10-16A. The built-in test voltage is 10/50/100/250/500/1000V adjustable. The instrument has the advantages of high precision, good stability, showing a rapid, easy reading, applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as the resistance value of the test as well as insulating materials electrical and electronic products insulation resistance measurement. The instrument can measure the resistance, and can directly measure the weak current. 

Instrument is fully consistent with and better than the national standard GB1410 " solid electrical insulating materials, insulation resistance, volume resistivity and surface resistance test method " and " American Standard ASTM D257 DC resistance or conductance of insulating materials test methods " and other standards.

Two, volume resistivity surface resistivity tester main features

Resistance measuring range 0.01× 104 Ω～ 1× 1018 Ω

Current measurement range of 2× 10-4A ～ 1× 10-16A

Small volume, light weight, high accuracy

Resistance, current double display

Good performance is stable, easy reading

All the test voltage （ 10/50/100/250/500/1000V ） test resistance results in reading, is removed from the old high resistance meter in different test voltage or different scale should be multiplied by the coefficient of the inconvenient trouble, allowing the measurement of high resistance as the multimeter is used to measure the general resistance of samples is simple.

Not only can measure high resistance and micro current

Wide application: applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as resistance testing electrical and electronic products insulation resistance measurement

Three, volume resistivity surface resistivity tester technical indicators

The 1 resistor measurement range: 0.01× 104 Ω～ 1× 1018 Ω.

The 2 current measurement range : 2 × 10-4A～ 1 × 10-16A

3 double header display: 3.1/2 LED display

4 built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V

5 basic accuracy: 1% （ note ）

6: use environment temperature: 0℃ ~ 40 ℃, relative humidity <80%

7 built-in test voltage: 10/50/100/250/500/1000V arbitrary switching

The 8 power supply forms: AC 220V, 50HZ, power consumption is about 5W

Four, volume resistivity surface resistivity meter working principle

According to the Ohm's law, the measured resistance is equal to voltage is applied through Rx V divided by the current I. The traditional high resistance meter is the working principle of measuring voltage V fixed, by measuring the current flows through the sampling resistor I to get the value of resistance. From Ohm's law can be seen, because the current I is inversely proportional to the resistance, but not proportional to the resistance, so the display value is nonlinear, namely the resistance to infinity, the current is zero, i.e., zero is∞, in the vicinity of the scale is very dense, with a low resolution. The scale is nonlinear. Because the measurement of different resistance, the voltage V also vary, so the average high resistance meter is poor accuracy, low resolution.

At the same time measure the voltage across the resistor V and the current through the resistor I, through the interior of the large scale integrated circuit to complete the voltage divided by the current calculation, and then the results obtained after A/D conversion to digital show resistance, even if the voltage across the resistor V and the current through the resistor I is changed at the same time, the display resistance value is not as common due to high resistance meter that measured voltage or current change of V I change, so, even if the measured voltage, resistance, power supply voltage is measured the changes in the results have little effect, the measurement accuracy is very high （ patent ）, theoretically the error can be zero, while the actual error can be done a few thousandths or extremely few.

Typical application

1 measurements of anti-static shoes, conductive shoes resistance value

2, measurement of the antistatic material resistance and resistivity

3, measurement computer room with movable floor system resistance

4, measurement of insulation resistance （ rate）

5, photodiode dark current measurement

6, physics, optics and materials research

Canton company other insulating materials testing instruments:

BDJC-0-100KV dielectric breakdown testing instrument

BDJC series insulating materials at power frequencies of dielectric breakdown test instrument

BDJC series voltage dielectric strength test apparatus

BDJC series voltage breakdown testing instrument

BDJC series insulating paint film breakdown strength tester

BDJC capacitor voltage breakdown testing instrument

EST-121 volume surface resistivity measuring instrument

GDAT-A dielectric loss tester / dielectric constant test

GDAT-C model dielectric constant dielectric loss tester

BDH leakage resistance tester

BDH-B arc resistance tester