Peppers防爆接头附件（locknuts, earthtags, sealing washers

EPIN英国Peppers防爆格兰，英国Peppers防爆变径接头，英国Peppers防爆堵头，英国Peppers防爆呼吸阀，英国Peppers防爆密封接头，英国Peppers防爆螺纹适配接头，上海颐品自动化，技术：

英国Peppers防爆堵头，防爆变径，防爆呼吸阀Peppers cable Gland

上海颐品自动化，：

Including type No’s: A C D P E *           B           S           N           A ACDPE Series Breather Drain provides a method of effectively draining any moisture within an enclosure whilst allowing the air inside the enclosure to breathe with the surrounding atmosphere. ACDPE series breather drains maintain Increased Safety Exe method of explosion protection and IP66 for IEC type applications.   CERTIFICATION CENELEC SIRA99ATEX3050U I M2 II 2DG EExe I/II; II 2DG E Exe (Glass Filled Nylon and Aluminium) CSA / A Ex Class I, Zone 1, Exe II; Class I Division 2, Groups ABCD GOST R-Exe II POCC GB MΠ14.B00030 IECEx Ex e II IECEx SIR 08.00244 APPLICATIONS Internal Dust Seal provides ingress protection to IP66 and 4x, with the largest possible pore size to aid draining, whilst retaining filtration capabilities that remove debris from the moisture and retains it on the surface where it can easily be removed with compressed air. Additionally the structural strength and chemical resistance characteristics of the material enable the filter to meet the requirements of hazardous area installations Caslated Locknut allows moisture to pass between the locknut and the enclosure, draining via holes in the thread without any build up of moisture in the bottom of the enclosure Captive ‘O’ Ring Seal is located within a recess on the face of the breather drain again optimising ingress protection, ensuring the ‘o’ring is not displaced during installation and helping protect the ‘O’ ring from the environmental damage External Drainage via two ports optimises ingress protection without compromising the draining capabilities INGRESS PROTECTION IP66, CSA Enclosure Type 4x, NEMA 4x IMPACT RESISTANCE 20Nm. (7Nm GF Nylon and Aluminium) OPERATING TEMPERATURES -50ºC to +85ºC MATERIALS Brass CZ121 (ACDPEB) 316 Stainless Steel (ACDPES) Aluminium Alloy (ACDPEA) 30% Glass Filled Nylon (ACDPEN) VARIATIONS Clearance hole (10): 10mm length of thread, supplied complete with a caslated locknut and having 2 holes in the thread wall positioned directly opposite each other Threaded Entry: 15mm length of thread, either supplied with or without caslated locknut and having 3 holes in the thread wall, offset to provide a 9mm range to accommodate differing wall thickness’ THREADS ISO Metric; NPT; NPS; ISO Pipe Thread (BSP Taper, BSP Parallel); PG SEALS The standard ‘O’ Ring material is Nitrile PLATING Zinc (ZP); Nickel (NP); Tin (TP); Electroless Nickel (EN) EXAMPLE PART NUMBER Sample: ACDPEb/NP/M20/15 ACDPEb - Breather Drain type and material (Brass) NP - Nickel plating M20 - Male thread size 15 - Male thread length (15mm) and drain holes in thread (x 3 offset)

DIMENSIONS Size Hex A/F Hex A/C Thread Length Head Length

M20 - 1.2h NPT 28.6mm 32.9mm 10 (2 Hole) or 15 (3 Hole) 15mm M25 - 3.4hNPT 34.9mm 40.2mm

All Dimensions are in Millimetres

NOTES: 30% glass filled nylon variations are only available with 15mm length of thread version and are supplied with or without a brass caslated nut Installation instructions are supplied with the breather drain, the instructions must be read prior to installation and adhered to in full Unless otherwise stated ISO Metric entry threads have a 1.5mm pitch Where metallic breather drains are fitted into non-metallic Increased Safety Exe enclosures they must be included within the earth circuit of the system

 

Part of our Accessories Range 2008 Catalogue Page 7.4.1   A full range of accessories including locknuts, earthtags, sealing washers, serrated washers and shrouds for use with all our cable glands     AVAILABILITY ACCESSORY TYPE GLAND TYPES/SIZE THREAD TYPES THREAD TYPES THREAD TYPES THREAD TYPES THREAD TYPES THREAD TYPES Locknuts provide a method of securing a threaded entry component into a piece of equipment Brass (ACBLN) All M16 to M100 1/2" to 4" 1/2" to 4" PG7 to PG48 F48 316 Stainless Steel (ACSLN) 316 Stainless Steel M16 to M100 1/2" to 4" 1/2" to 4" PG7 to PG48 F48 Aluminium Alloy (ACALN) Aluminium M20 to M63 - - - - Nylon (ACNLN) Nylon M20 to M63 - - PG7 to PG48 - Earth Tags provide an earth bond connection for an entry component Brass (ACBET) All M16 to M100 1/2" to 4" 1/2" to 4" PG7 to PG48 F48 Aluminium Alloy (ACAET) Aluminium M20 to M63 - - - - IP Sealing Washers are fitted between an entry component and the equipment to maintain the IP rating of the equipment Nylon (ACNSW) All M16 to M100 /2" to 4" /2" to 4" PG7 to PG48 F48 Red Fibre (ACFSW) All M20 to M75 - - - - Serrated Star Washers can be used in conjunction with a locknut to provide additional fixing security and improve bonding 316 Stainless Steel (ACSLN) All M16 to M100 1/2" to 4" 1/2" to 4" PG7 to PG48 F48 Shrouds can be used to protect the gland from the surrounding environment PVC (ACSPVC) 16 to 100 Shrouds are not available for all glands, please see specific gland page for exact details PCP (ACSPCP) 16 to 85 LSOH (ACSSIO) 16 to 85

NOTES: As standard ISO Metric threads are supplied with a 1.5mm pitch up to and including M75 and a 2.0mm pitch for sizes above M75

 

中国区分销商：
上海颐品自动化科技有限公司
Shanghai Epin Automation Co.,Ltd.

Website:www.epinautomation。。ｃｏｍ
:sales@epinautomation.com
*:

因为专业，所以放心！